Guide

How to Empty a Paper Shredder

Updated on · By the Paper Shredders Info team

Here's how to empty a paper shredder cleanly: unplug it, open the bin slowly over a laid-out bag, and lift the shreds out in one block instead of tipping them out. Wipe the bin, replace the bag and recheck the machine before the next run.

On this page (9 sections)
  1. What should you gather before you open the bin?
  2. How do you remove the bin and empty a paper shredder?
  3. How do you keep paper scraps from flying everywhere?
  4. Should you empty a paper shredder over a trash can or into a bag?
  5. What should you check on the cutting head while the bin is out?
  6. How do you reset the shredder after emptying?
  7. Which habits keep emptying quick and tidy?
  8. When should you replace the bag or skip a bag entirely?
  9. The short version

Here's how to empty a paper shredder without scattering scraps: unplug it, slide a bag over the bin before you open the head, and lift the shreds out as one block. Wipe the bin, fit a fresh bag and run a short test before the next stack goes in.

The step people skip is the order. Open the bin first and the cross-cut confetti is already airborne, so set up the bag and the floor cover before the lid comes off.

What should you gather before you open the bin?

Set out a large plastic bag, a few old newspaper sheets and a damp cloth before you touch the head. Doing the setup first is what keeps the shreds off the floor, because you never stand over an open bin with your hands full.

Clear a flat area beside the machine and lay newspaper or a flattened cardboard box on it. That catches the few scraps that always escape when you lift a bag out.

Keep the replacement bag within reach so you can slide it over the bin straight away.

Check the fill level through the window or by lifting the head slightly. If the shreds touch the underside of the cutting head, stop running the machine until it's empty.

A clear workspace and a ready bag turn a messy chore into a two-minute job.

How do you remove the bin and empty a paper shredder?

Switch the shredder off, unplug it and lift the head straight up, then set the head down on its side where it can't tip. Pull the bin out by its handle and keep it level as you move it.

Hold the bag's open end over the bin mouth as you tip the bin toward the bag. Let the shreds slide in rather than shaking the bin, which sends scraps into the air.

If the bag sits inside the bin already, gather its edges and lift the whole load out in one motion.

For a bin without a liner, tip the shreds slowly onto the newspaper and fold the corners into a bundle. Wipe the bin's inside and rim with the damp cloth, since dust clings to the walls.

Then fit a fresh bag over the lip, fold the top edge down the outside, and lower the bin back into the cabinet.

Which bag suits a typical home shredder?

Choose the Tru Red 15.8-gallon bags for a shredder bin near this size, since they hold a full load without tearing. The bag thickness of 0.5 mil is light enough to fold over the bin rim yet strong enough to carry out full of strips.

The bags measure 27.6 inches high by 24.6 inches wide and come 50 to a box. Clear plastic lets you see when the bin is getting full without lifting the head.

Staples makes them for personal shredders, and the size fits most home models rather than large office units.

Measure your bin's width and height before you order, because a bag that's too small will slip off the rim. Skip these if you own a compact bin well under 10 gallons or a heavy-duty office cabinet.

How do you keep paper scraps from flying everywhere?

Lift slowly and never shake the bin or bag, because most mess comes from fast movement, not from static. Hold the bag below the bin rim so falling shreds have a short, controlled drop.

Cross-cut shreds are light and pick up static, so they cling to the bin walls and each other. A damp wipe before you tip the bin releases that cling.

Move the bag close to the bin mouth and keep both hands on the load rather than tipping from a height.

If you're shredding by hand into a basket, line the basket with a bag before you start so the whole batch comes out at once. Work over the newspaper so any stray scraps land there.

Fold the paper up at the end and tip the contents into the trash bag, not across the room.

Should you empty a paper shredder over a trash can or into a bag?

Line the bin with a bag and carry the bag to the trash can rather than tipping shreds straight into a can from the shredder. This gives you one controlled transfer instead of two.

Tipping a loose bin over a tall trash can drops the load several feet. That height is where cross-cut strips scatter and where static pushes them onto the floor.

A bag keeps the load together, and the newspaper underneath catches anything that spills.

Bagging also protects the bin's inside from sticky dust. The dust that comes off cut paper settles and binds, and a bag holds most of it so the bin stays cleaner between wipes.

Tie the bag before you carry it out so nothing escapes on the way.

What should you check on the cutting head while the bin is out?

Look for packed paper around the cutters and clear it with tweezers or a brush while the bin is empty. This is the easiest moment to spot a jam building up.

Check the underside of the head for strips wrapped around the cutting shafts. A build-up here strains the motor and can lead to a jam next time.

Use a soft brush or tweezers and keep your fingers clear, even though the machine is unplugged.

This is also when owners often lubricate the cutters, since the bin is already open and the work area is clear. For a step-by-step view of what the blades do, see how does a paper shredder work.

Why lubricate right after emptying?

Many makers recommend lubricating each time the bin is emptied. Lubrication conditions the cutters, helps them run smoothly and can reduce jams caused by dry, dusty blades.

The Amazon Basics lubricating sheets make this a clean job. You feed one 8.4 by 6 inch sheet straight into the paper slot and the cutters shred it, coating themselves as they go.

A 24-pack gives you a sheet for each empty, and the vegetable oil and recycled paper construction means no oily bottle to handle.

Skip the sheets if your machine's instructions call for liquid oil only. Follow the maker's guidance for how often to lubricate, since a few months of light home use needs less than a busy office.

Who should keep a bottle of shredder oil instead?

Choose the Fellowes Powershred 16 oz oil if you want to apply lubricant by hand along the cutter line, which suits some cross-cut and micro-cut models. The squeeze bottle has an extended nozzle that reaches the blades without dripping.

Fellowes advises oiling each time you empty the wastebasket or at least twice a month. That schedule lines up with the emptying routine here.

Apply the oil along the paper entry, then run the machine briefly in reverse to spread it over the cutters.

Skip it if your shredder uses lubricating sheets or you'd rather not handle liquid oil. A 16 oz bottle lasts a long time for a home office.

How do you reset the shredder after emptying?

Replace the bin fully, press the head down until it clicks, and run a short test before adding a big stack. Most machines won't run with the bin pulled out or seated loosely.

Push the bin in until it meets the stop, then lower the head straight down onto the cabinet. A safety interlock usually refuses to start until both are seated, which protects you from reaching into the cutters while the machine runs.

Plug the shredder back in and set the switch to auto. Feed one or two sheets and listen for a smooth run.

If the motor stalls or the reverse light comes on, stop and clear the cutters before you continue.

Which habits keep emptying quick and tidy?

Keep a bag in the bin at all times and empty when shreds reach the fill line, so every empty takes a minute rather than becoming a cleanup. Small habits add up over a year of shredding.

  • Line the bin before shredding starts, not when it's full.
  • Empty when the shreds reach the line, and don't compact them by pressing down.
  • Wipe the bin's inside each time you swap bags.
  • Check the cutters for wrapped strips while the bin is out.
  • Carry the tied bag straight to the trash or recycling.

Storing the machine near a trash can shortens the carry. Keeping a spare pack of bags beside the shredder means you never run out at the wrong moment.

That routine also makes the how to dispose of a paper shredder step easier when the machine reaches the end of its life.

When should you replace the bag or skip a bag entirely?

Use a bag for everyday emptying, and skip it only if your bin is awkwardly shaped or your machine's maker says not to. A bag suits square and rectangular bins with a flat rim; it may slip on a rounded or tapered bin.

Check the fit by folding the bag's top edge over the rim. If it sags into the bin or leaves gaps, the shreds will catch under it.

Measure the bin's opening first, because a bag meant for a 15-gallon cabinet can swamp a compact bin.

Skip the bag if the bin is small enough to tip directly into a wastebasket without scattering. Bagging pays off most when you shred often and want the bin to stay clean.

If you're comparing machines and want to know which brands build bins that lift out easily, our guides to the Aurora paper shredder range and Fellowes paper shredder models cover the practical differences.

The short version

Empty a paper shredder in this order: unplug it, set out a bag and floor cover, lift the head, lift the shreds out in one block, wipe the bin and fit a fresh bag. Then seat the bin, plug in and test before the next stack.

Keep a pack of liners beside the machine and empty at the fill line rather than waiting for a jam. A clear bag and a quick wipe each time is the whole routine.

Frequently asked questions

How often should I empty the shredder bin?

Empty it when the shreds reach the fill line or sit within about 2 inches of the top, whichever comes first. A full bin pushes shreds back into the cutters and strains the motor, so don't wait until the head won't sit flat.

Is it safe to shred without a bag?

Yes, most shredders run fine without one. A bag simply makes the next empty cleaner and faster, because you lift the whole load out instead of scooping loose strips from the bin.

Can I empty a shredder while it's plugged in?

No. Switch it off and unplug it first, so the cutters can't start if the power switch or sensor is bumped while your hands are near the head.

What should I do with the shreds after emptying?

Tie the bag shut and recycle the paper where your town accepts it. For security-level shredding that mixes plastic cards or discs with paper, check local rules and the shredder guide to how to dispose of a paper shredder waste before mixing loads.